Accuslide Attachment

The Most rigid, powerful, reliable product of it's kind the Accuslide CNC attachment is available for: Hardinge HSL - Hardinge DV-59 - Hardinge HC - Hardinge AHC - Hardinge DSM-59 - Hardinge DSMA - Wade - McLean - Tsugami - Steel - Habbegger - Feeler FTS-27 - FHR - FSL - Monarch - And a variety of engine lathes.

Accuslide's modular design is easily installed and allows you to build as you grow!

  • Spindle Encoder - Easily mounts to existing holes in Hardinge casting.
  • Power Collet Closer - Oil mist lubrication for extended bearing life.
  • Complete Spindle Rebuilds - Available upon request.
  • Collet Overide Switch - manual open close for easy setup.
  • Baldor Spindle Motors - upsized for increased torque at lower speeds.
  • Complete Refinishing - Your Hardinge lathe restored to original finish quality.
  • M08 Coolant - controlled through Fagor CNC
  • Hardinge Compatible Tooling
  • Fagor - 8025T Control
  • Manual Pulse Generator
  • NSK linear guides - are dowel pinned.
  • All components precision ground.
  • Black oxide finish on all machined surfaces.
  • Simple Construction of just 5 components.
  • 25mm NSK linear bearings.
  • Precision ground ball screws.
  • Precision Dovetail machined directly into the base plate
  • NSK 25mm precision guideways are twenty percent larger than guideways found on competitive products. Larger bearings with greater surface contact means greater rigidity, longer life, better finishes, and more cutting capacity. All linear rails are dowel pinned to precision ground steel platens. Loc-tight sealant is used on hold-down bolts to insure against fatigue or vibration.

    Precision ground, zero backlash ballscrews from NSK and Yena are built to our rigid specifications. Our one piece integrated yolk and ballnut is precision ground to ensure failsafe alignment with fewer components. At ten threads per inch Accuslide can guarantee twenty millionths resolution, with over six hundred pounds of thrust.

    NSK precision thrust bearings are mounted to steel support platens that serve a dual purpose as motor mount, and bearing support platform. Ground steel construction ensures less fatigue under maximum cutting loads.

    QMC, Rare-Earth, High Torque motors, provide maximum thrust with greater acceleration. They are manufactured with oversized bearings and key-ways rather than set-screws. Motors are nearly submersible with O-ring seals.

    Deutsch waterproof connectors, with potted back-shells are wired for the Accuslide by Glenair's aerospace cable division. Fully shielded twisted pairs are wrapped in Teflon cover to insure flexibility and durability in a hostile environment.

    Accuslide Options

    Air actuated collect closer enables the operator to quickly release and grip parts.

    State of the art AC Spindle Drives give you spindle speed control via "S" code at the control. Easy installation. No electrical wiring.

    Fagor Handwheel accessory

    Full chip enclosures for all Hardinge models include gas-shock assist over-head door for easy setup.

    C-Axis control interface with DC Servo drive spindle can give you a productive edge when you are looking to do side hole drilling, milling, or wawing.

    Every Accuslide is capable of direct interface to any barfeed unit.

    Interchangeable tooling systems are the quickest way to change complete tooling setups.

    Auto loaders are available on either a generic or turnkey basis. Air actuated components can be interfaced to optional PLC or actuated by M-Function.

    A Forward/Reverse contactor box with a minimal interface can save you money whtn the job just doesn't require a great deal of automation.

    Threading can only be accomplished if there is a direct interface between spindle and slide motion. With the application of a 1024 line encoder on the spindle the controller can develop any thread you desire.

    Accuslide Machine Specifications
  • X Axis Travel 11.75"
  • Z Axis Travel 7.5"
  • Spindle Motor 5 HP
  • Spindle RPM (variable) 0-3,450 RPM
  • Maximum bar size 1 1/16"
  • Standard Hardinge Tool Holders 1/2"
  • Axis thrust 600 lbs.
  • Feed Rates 300 ipm
  • Rapid Travels 600 ipm
  • Compressed Air (clean, dry) Requirements 5 SCFM
  • Voltage 230 VAC
  • Power Requirements 7.5 KVA
  • Machine Weight 2,800 lbs.


  • 3-Axis Lathe
    Accuslide
    Glossary Of Terms
    Replacement Lathes
    Used Lathes
    GT-ISL-25 Lathe
    Turning Machines
    CNC Equipment
    CNC controllers
    CNC New, Inc. 1414-B S. Ritchey St. Santa Ana, CA 92705
    Phone: 1-800-662-3351 or 1-949-218-4393 Fax: 1-949-388-5615
    Email:
    copyright CNCNEW Inc. All rights reserved